







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Inglewood Homeowners Choose Belgard Construction
We provide independent Belgard construction service in Inglewood, and what sets our Belgard work apart is the base and drainage spec behind every paver surface we build or repair. Belgard is a hardscape brand – segmental pavers and retaining wall blocks – and the paver itself is rarely the thing that fails. The ground under it fails first. We treat base compaction, edge restraint, and water management as the real job, which is why our Belgard driveways, patios, and wall systems hold their line through Inglewood’s dry summers and damp coastal winters.

Construction Inglewood is an independent Belgard service provider. We are not affiliated with, authorized by, or sponsored by Belgard, and we’re not a Belgard dealer. We install, repair, and service Belgard products with quality materials that fit them. Our technicians have up to 14 years of experience with segmental paving systems.
Call (844) 320-4724 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm.
Why Trust Construction Inglewood for Your Belgard Construction?

Belgard systems are modular, which sounds simple until you’re the one deciding how deep the base goes and what holds the edge. Our technicians have worked with these products long enough to read a failing installation by its symptoms. Ruts in a driveway point to a thin base or compaction skipped in lifts. Efflorescence on Cambridge Cobble usually traces to water sitting under the units with nowhere to drain. A leaning Weston Wall nearly always means missing geogrid or clogged drainage aggregate behind the blocks. Those are the failures we spend our time preventing and correcting.
We source genuine Belgard pavers and wall blocks so repairs and expansions match the existing line instead of sitting visibly different six months later. For base materials and joint sand we choose quality products rated for the job – not cheap substitutes that break down and drag the whole installation with them. Any manufacturer warranty that applies to your Belgard product stays intact because we follow the installation standards those warranties depend on: proper excavation, compacted base, correct edge restraint, clean drainage.
Belgard is one of six paver brands we work with, alongside Unilock, Techo-Bloc, Tremron, Cambridge Pavers, and Oldcastle. That lineup matters. It means we’re recommending a base and drainage approach because it’s right for your property, not because it’s the only system we know. One contractor from the driveway to the ridge line – and the hardscape in between. Call (844) 320-4724 to talk through your project.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Belgard Construction Problems We Fix in Inglewood
Segmental paving fails in predictable ways. Here’s what we see on Belgard installations around Inglewood, and what actually causes each one.
- Lafitt Rustic Slab pavers rutting and shifting on driveways. Vehicle loads are unforgiving. When the base was poured too thin, or compacted in one thick pass instead of proper lifts, the pavers settle unevenly within a season or two. Expansive clay soils common on Inglewood’s small lots make it worse: the ground moves with moisture, and a weak base can’t hold against that movement. The fix is almost always under the pavers, not on top of them.
- Cambridge Cobble spalling or efflorescence. Efflorescence is that chalky white bloom – it’s salts migrating to the surface as moisture moves through the units. It shows up when water gets trapped beneath pavers because drainage falls the wrong way or the base doesn’t drain. Actual spalling, where the face flakes off, points to a mix or installation problem and often to sealing too early or in the wrong conditions. Correcting the slope and drainage is the first step.
- Weston Wall segments bulging or leaning. A retaining wall holds back soil and water pressure. Skip the geogrid reinforcement or backfill with clean drainage aggregate, and the wall starts to lean as pressure builds. Inglewood’s damp winters load that soil with water. A small lean doesn’t stay small. It needs to be opened up and rebuilt correctly before the whole face fails.
- Joints washing out and weeds coming through. Polymeric sand is the reason a paver surface looks finished. Applied too thin, or in wet conditions that stop it from setting properly, it rinses out at the first hard rain. Once joints open, weeds find them and the pavers start to loosen. Re-sanding correctly is a quick job when caught early; left alone, it leads back to a base problem.
- Settling at edges and along the garage apron. Edge restraint is what keeps a driveway from spreading outward over time. Inglewood has a lot of 1920s to 1950s homes where the apron and approach grades were set before anyone thought about today’s vehicle weights. When the restraint is missing or broken, the outer course walks and the whole surface loosens. We rebuild the edge, not just the pavers.
Belgard Parts and Our Repair-vs-Replace Approach

Matching an existing paver line matters more than people expect. Colors and textures vary between production runs, so a repair that uses the wrong block stands out permanently. We source genuine Belgard pavers and wall blocks to match your existing line, and for base aggregate and polymeric sand we use quality materials rather than off-brand substitutes that fail early and take the surface with them. We’re not a dealer and we don’t claim to stock every line – we source what your repair needs.
The repair-or-rebuild call comes down to what’s moving and why. A single cracked unit or a few worn pavers gets swapped individually. Sections that have sunk or rock underfoot are a base problem, and spot patching those just delays the same failure. Rebuilding the affected area – excavating, recompacting the base in lifts, resetting the Belgard units, correcting slope – is more reliable and usually cheaper over time than patching twice. Our technicians have up to 14 years of experience making that call.
Call (844) 320-4724 for a free estimate.
Our Belgard Service Process – Step by Step
Every Belgard job follows the same sequence, whether it’s a repair or a new installation.

- 1
Diagnosis. We look at the whole system – pavers, base, edge restraint, and drainage – because the visible symptom rarely tells the whole story. Shallow ruts might read as worn pavers but trace to a thin base.
- 2
Base and drainage evaluation. We check soil conditions, slope, and how water currently leaves the area. On Inglewood’s clay-heavy lots this is where most decisions get made.
- 3
Repair or install. We excavate to proper depth, compact in lifts, set edge restraint, and lay the Belgard units to the correct grade so water runs away from your home, not toward it.
- 4
Joint sand and finish. Polymeric sand goes in dry conditions, at proper depth with the joints filled fully – not the thin dusting that rinses out.
- 5
Warranty and walkthrough. We close out with a written record of the materials and scope so any manufacturer warranty on your Belgard product stays defensible. The written estimate sets the final price before any work starts.
See the difference
Before
After
Before
After
Before
AfterBelgard Products We Service and Install in Inglewood
We work across the Belgard hardscape line: segmental pavers for driveways, patios, walkways, and pool decks, and segmental retaining wall block systems, plus the base, edge restraint, and polymeric sand that hold them together. The lines you’ll most often see on Inglewood properties include Lafitt Rustic Slab, Cambridge Cobble, Weston Wall, and Dublin Cobble. We repair and expand existing installs to match your line, and we build new installations from the base up. Our focus sub-services are paver driveway installation, paver patio installation, and driveway replacement. The written estimate sets the final price on all of it.
We Also Service These Brands
Belgard is one of many name-brand systems we work with. For a full property scope you’re also covered on KraftMaid cabinetry, Kohler fixtures, GAF roofing, and PGT windows and doors, alongside Unilock, Techo-Bloc, and Tremron in hardscape. That breadth means one contractor handles the driveway, the patio, and whatever else your project touches. You choose the material, we handle everything else.
FAQs – Belgard Construction Service in Inglewood

No. We’re an independent Belgard service provider, not a dealer, and we’re not affiliated with or authorized by the manufacturer. We install, repair, and service Belgard products using quality materials that fit them. Call (844) 320-4724 to discuss your project.
Usually yes. We source genuine Belgard pavers to match your existing line. Color and texture can shift slightly between production runs, so we match as closely as the current line allows. For best results, plan expansions at the same time as repairs so any variation blends in. Call (844) 320-4724 for a free estimate.
Spalling usually points to trapped moisture under the pavers from poor slope or drainage, or to sealing applied in the wrong conditions. Efflorescence – the white bloom – is a related symptom of water moving through the units. Correcting drainage and slope comes first. Call (844) 320-4724 to have it looked at.
Walls above a certain height almost always need geogrid and clean drainage aggregate behind the blocks, and Inglewood’s damp winters load retained soil with moisture that adds pressure. Building without it is the common cause of bulging and leaning. We confirm requirements against your local building code and engineer the wall to it. Call (844) 320-4724 for an assessment.
Wait until the pavers are fully dry and the joints are set – typically several weeks, and longer in damp weather. Sealing a wet or freshly installed surface traps moisture and can cause the very efflorescence you’re trying to prevent. We’ll tell you the right window for your installation with the written estimate. Call (844) 320-4724 to schedule.
Polymeric sand is the better choice here. It sets firm, resists washout through Inglewood’s winter rains, and blocks the weed growth that regular joint sand allows. It only works applied dry, at proper depth with joints fully filled. Call (844) 320-4724 for a quote on re-sanding.
Typical estimated ranges are below. The written estimate sets the final price.
| Belgard Service | Typical Estimated Range |
|---|---|
| Paver Driveway Installation | $7,000-$18,000 |
| Paver Patio Installation | $3,500-$11,000 |
| Driveway Replacement | $5,000-$14,000 |
Base conditions, drainage work, and wall reinforcement drive the final number more than the pavers themselves. Call (844) 320-4724 for a free estimate.
Book Your Belgard Service in Inglewood, CA
Whether you’re repairing a settled driveway or building a new Belgard patio, we’ll spec the base and drainage correctly and put it in writing before work starts. Free estimates, written line-item quotes, and fixed pricing with no change orders. Call (844) 320-4724. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Construction Inglewood.












