







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Inglewood Homeowners Choose Toto Construction
Construction Inglewood provides independent Toto fixture service and installation in Inglewood, CA, for the toilets, bidet seats, and sensor faucets already sitting in local bathrooms. Our technicians have up to 14 years of experience, and we fit genuine Toto replacement parts instead of generic aftermarket pieces that cause repeat running-toilet callbacks. What makes our Toto work different is that we treat the fixture as part of the bathroom, not a standalone box: we check the closet flange, the supply line, the shutoff, and the GFCI outlet a Washlet seat depends on. We are not authorized, sponsored, or endorsed by Toto. If you want that conversation to start with a free estimate, call (844) 320-4724.

Why Trust Construction Inglewood for Your Toto Construction?

Toto builds a specific kind of fixture, and the service habits that fit it are specific too. Drake two-piece toilets (CST743 and CST776) live or die on the flapper seal and fill valve holding clean contact; Ultramax II one-piece units (MS604114CEFG) add a tank-to-bowl gasket that owners often mistake for a cracked bowl. Washlet bidet seats – the S550e, C5, and K300 – bring wands, nozzles, seat sensors, and control boards into the bathroom, and each has its own wear pattern. Our technicians work on these platforms regularly, so the diagnosis starts from a known failure pattern instead of a guess.
We install quality parts that fit Toto equipment and we keep the work warranty-safe. That means correct sealing surfaces, proper torque on connections, and a fresh wax ring every time a floor-mounted toilet comes up. We’re an independent service provider, so our credibility rests on familiarity with the product line, not a manufacturer badge. Whether you’re in Inglewood or anywhere nearby, the phone line stays open: call (844) 320-4724. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Toto Construction Problems We Fix in Inglewood
- Drake and Ultramax II fill valve and flapper wear. The symptoms show up as phantom running, a weak flush, or a flapper that no longer seats. Inglewood’s hard water leaves mineral deposits on the seal surface, so a flapper that closed cleanly in its first years starts leaking by. A tired fill valve makes it worse by failing to shut off at the right level.
- Washlet nozzle and wand faults. Clogged or scaled wand nozzles are the most common bidet-seat complaint, showing as a weak spray or a wand that doesn’t extend. Control-panel and seat-sensor failures are the other side of it, where the unit stops responding to the remote or the seat sensor. Hard water scale, not electronics, is usually behind the spray problem.
- Wax ring and closet flange leaks. On older Toto floor-mounted toilets, a failed wax ring or a cracked flange lets water seep under the tile. The tell isn’t a puddle. It’s a soft spot in the floor or a stained subfloor near the base, and it’s easy to miss until the flooring gives.
- Supply-line and angle-stop seepage. A slow weep at the angle stop or supply line keeps the bowl area damp and can corrode the shutoff over time. We replace the supply line and shutoff rather than tightening a failing connection and calling it done.
- Tank-to-bowl gasket weeping on one-piece Ultramax units. A one-piece toilet can look like it has a cracked bowl when the real problem is the gasket between tank and bowl. Water tracks down the outside of the porcelain and pools quietly at the base, which sends owners toward replacement when a gasket and reset is the actual fix.
Toto Parts & Our Repair-vs-Replace Approach

We fit genuine Toto replacement parts – fill valves, flappers, gaskets, wax rings, Washlet nozzles, and seats – because aftermarket flappers and fill valves are the leading cause of repeat running-toilet callbacks on Drake and Ultramax fixtures. We don’t describe our parts as OEM stock or claim to be a Toto dealer. We source parts that fit and install them correctly.
Our repair-vs-replace call comes down to porcelain and flange condition. If the bowl and tank porcelain are sound and the flange can be secured, repair is almost always the right call – a Toto that flushes weakly because of a scaled flapper usually needs a valve, flapper, and gasket, not a new toilet. Replacement only makes sense when the porcelain is cracked or the flange is beyond re-securing. Either way, the scope gets written down before work starts, so the estimate is what you pay. Call (844) 320-4724 for a free estimate.
Our Toto Service Process – Step by Step
- 1
Diagnosis. We start by listening to the symptom – running, weak flush, wand spray, sensor fault, or damp floor. Then we check the tank internals, the seal, the closet flange, the supply line and shutoff, and any Washlet outlet, so the fix addresses the actual cause.
- 2
Repair or install. With the scope agreed, we replace the failing parts with Toto-compatible ones, pull the tank on one-piece units when a gasket is suspected, and reset floor-mounted toilets on a fresh wax ring with the flange checked for cracks.
- 3
Test. We run the flush cycle, confirm the fill valve shuts off cleanly, check the shutoff and supply line hold, test the Washlet spray and sensors, and verify the seat outlet is on a GFCI-protected circuit.
- 4
Warranty. The work is documented, the parts carry their own manufacturer warranty, and we tell you what would signal a return problem so you’re not guessing.
See the difference
Before
After
Before
After
Before
AfterToto Products We Service & Install in Inglewood
We service and install Toto two-piece gravity toilets including the Drake line, one-piece toilets like the Ultramax II, Washlet bidet seats in the S550e, C5, and K300 ranges, and EcoPower and Eco Series sensor faucets and flush valves. That covers the fixtures found in most Inglewood bathrooms – from a straightforward toilet reset to a full bidet-seat swap during a remodel. We don’t claim to stock or carry these products. We service what’s there and install what you choose. If a bathroom remodel will move the toilet, we coordinate the plumbing and set the fixture back correctly at the finish end of the project.
We Also Service These Brands
Toto is one line among many. Construction Inglewood works across KraftMaid cabinetry for a bathroom vanity, Kohler and Moen fixtures alongside Toto toilets, GAF roofing when a project reaches the roof line, and PGT windows if natural light comes into it. That means your bathroom remodel runs through one contractor instead of three. Call (844) 320-4724 for a free estimate.

FAQs – Toto Construction Service in Inglewood

Is Construction Inglewood authorized by Toto? No. Construction Inglewood is an independent service provider and is not authorized, sponsored, or endorsed by Toto. We work on Toto fixtures because our technicians know the platform, and our credibility comes from that familiarity, not a manufacturer badge.
Do you use quality parts that fit Toto equipment? Yes. We fit genuine Toto replacement parts – fill valves, flappers, gaskets, wax rings, and Washlet nozzles and seats – because aftermarket valves and flappers are the top cause of repeat running-toilet callbacks on Drake and Ultramax fixtures. We describe them as parts that fit, not as OEM stock.
How long does Toto service take? A toilet repair – fill valve, flapper, and gasket with a fresh wax ring – is a short visit. A Washlet repair or a bidet-seat swap is shorter. A bathroom remodel that moves the toilet or adds a GFCI outlet for a Washlet runs on a longer schedule set by the written estimate. Call (844) 320-4724 for an exact quote.
What kinds of Toto products do you cover? Two-piece gravity toilets like the Drake, one-piece units like the Ultramax II, Washlet bidet seats in the S550e, C5, and K300 ranges, and EcoPower and Eco Series sensor faucets and flush valves.
Will service void my Toto warranty? Correct service with proper parts and sealing doesn’t void a fixture warranty, and quality parts carry their own coverage from their manufacturer. We work warranty-safe: correct sealing surfaces, proper connections, fresh wax rings. Call (844) 320-4724 with your fixture details and we’ll walk through what applies.
How much does Toto construction cost in Inglewood? Toto fixture service is priced per job by estimate. When the Toto install sits inside a bathroom remodel, typical estimated ranges for Inglewood run as follows – the written estimate sets the final price.
| Service | Typical Estimated Range |
|---|---|
| Bathroom Remodel | $9000 – $28000 |
| Small Bathroom Remodel | $5000 – $12000 |
| Walk-In Shower Installation | $4500 – $12000 |
| Tub-to-Shower Conversion | $3500 – $10000 |
| Bathroom Vanity Installation | $800 – $3000 |
Call (844) 320-4724 for an exact quote – estimates are free.
Book Your Toto Service in Inglewood, CA
Whether it’s a Drake that won’t stop running, a Washlet that quit spraying, or a bathroom remodel that needs the Toto set back correctly, Construction Inglewood can help. Estimates are free and written line-item. Call (844) 320-4724. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Construction Inglewood.












